Get all the Information About EMC D-PSC-MN-01 Exam 2024 Practice Test Questions
Check Real EMC D-PSC-MN-01 Exam Question for Free (2024)
NEW QUESTION # 75
During the replacement of a failed hard drive, a key FRU, what steps should be followed to ensure proper installation?
- A. Confirming the slot and drive compatibility
- B. Ensuring the node is isolated from the network
- C. Performing a full data backup
- D. Verifying the drive firmware version matches the cluster
Answer: A,D
NEW QUESTION # 76
What is a critical aspect of external networking setup for PowerScale clusters?
- A. Establishing redundant connections
- B. Configuring VLANs
- C. Ensuring compatibility with legacy systems
- D. Implementing Quality of Service (QoS)
Answer: A
NEW QUESTION # 77
How should a PowerScale administrator approach the integration of a Hadoop ecosystem?
- A. By installing the Hadoop software on each node individually
- B. By creating separate storage pools for Hadoop and non-Hadoop data
- C. By ensuring that the HDFS protocol is correctly configured on all nodes
- D. By configuring the firewall to allow Hadoop-related traffic
Answer: C
NEW QUESTION # 78
Match each Dell PowerScale node to its description.
Answer:
Explanation:
NEW QUESTION # 79
According to Dell PowerScale best practices, which component may be replaced by the customer?
- A. Power supply
- B. Battery
- C. Fan
- D. M.2 vault card
Answer: A
NEW QUESTION # 80
A platform engineer needs to gather information about the configuration of a Dell PowerScale cluster. They are specifically interested in knowing which features are affected by upgrading firmware on a subset of the nodes.
Which command does the engineer need to execute?
- A. isi upgrade cluster view
- B. isi upgrade cluster list
- C. isi_gather_info
- D. isi_upgrade_helper
Answer: D
NEW QUESTION # 81
When cabling nodes, what practices should be followed to ensure a successful PowerScale installation? (Select two)
- A. Testing each cable for connectivity and signal integrity
- B. Using cables of standardized lengths to reduce clutter
- C. Labeling each cable according to its connection points
- D. Implementing structured cabling that adheres to industry standards
Answer: A,C
NEW QUESTION # 82
How can an administrator verify that a node is successfully shut down?
- A. Verify the LEDs on the front panel are not lit.
- B. Try to access a share on the node and verify the share is inaccessible.
- C. Execute the isi status -q command and see that the node is in an A-- status.
- D. Execute the isi status -q command and see that the node is in a D--- status.
Answer: D
NEW QUESTION # 83
What is the primary purpose of conducting a PowerScale node health check before maintenance?
- A. To ensure data replication is complete
- B. To identify any failing components
- C. To verify network connectivity
- D. To assess storage capacity utilization
Answer: B
NEW QUESTION # 84
Which action is critical when preparing the site for a PowerScale installation?
- A. Configuring the initial cluster network settings
- B. Preparing an inventory of all software applications to be used
- C. Setting up remote monitoring tools
- D. Ensuring appropriate environmental conditions, such as temperature and humidity
Answer: D
NEW QUESTION # 85
What preparatory action is necessary to facilitate effective troubleshooting during and after PowerScale rack installation?
- A. Setting up a temporary command center near the rack
- B. Creating a detailed network diagram
- C. Photographing each phase of the installation for reference
- D. Ensuring all tools and spare components are available on-site
Answer: C
NEW QUESTION # 86
What is the recommended action if a PowerScale node reports inconsistent data?
- A. Run a synchronization process with other nodes
- B. Remove the node from the cluster and replace it
- C. Isolate the node immediately and perform a data integrity scan
- D. Reboot the node to clear any temporary issues
Answer: C
NEW QUESTION # 87
A platform engineer plans to upgrade Dell PowerScale OneFS.
Which action must they consider during the pre-upgrade phase?
- A. Update firmware
- B. Install recommended patches
- C. Implement OneFS API
- D. Check supportability and compatibility requirements
Answer: A
NEW QUESTION # 88
What is the correct order of steps to repackage the shipping material for a Dell PowerScale cluster?
- A. 1. Stack the two folded outer sleeves above the ramp sections.
2. Band the unit with shipping straps.
3. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
4. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
5. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up. - B. 1. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
2. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
3. Stack the two folded outer sleeves above the ramp sections.
4. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
5. Band the unit with shipping straps. - C. 1. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
2. Band the unit with shipping straps.
3. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
4. Stack the two folded outer sleeves above the ramp sections.
5. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections. - D. 1. Stack the shipping bracket on the pallet. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
2. Apply the two collar sections to either side of the pallet and hold them in place with the package hood.
3. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections.
4. Stack the two folded outer sleeves above the ramp sections.
5. Band the unit with shipping straps.
Answer: B
NEW QUESTION # 89
A Dell PowerScale Gen 6 chassis is scheduled to be installed in a rack.
What is a valid recommendation?
- A. When the drive sleds and compute modules are removed, two people need to lift the chassis.
- B. When the drive sleds and compute modules are removed, one person is allowed to lift the chassis.
- C. When using a mechanical lift, the drive sleds and compute modules need to be removed first.
- D. When using a mechanical lift, two people are required to install the chassis into the rack.
Answer: A
NEW QUESTION # 90
During the installation of racks for PowerScale, why is it important to ensure proper alignment and leveling?
- A. To prevent physical strain on components
- B. To optimize space utilization within the data center
- C. To ensure ease of access for future maintenance
- D. To facilitate proper airflow and cooling
Answer: A
NEW QUESTION # 91
What protocols are essential for secure remote PowerScale cluster management? (Select two)
- A. RDP
- B. SNMPv3
- C. HTTP
- D. SSH
Answer: B,D
NEW QUESTION # 92
......
Use Free D-PSC-MN-01 Exam Questions that Stimulates Actual EXAM : https://pass4sure.validdumps.top/D-PSC-MN-01-exam-torrent.html